Navigation: Configuration > Configuration Guide (Web Mode) > Advanced Configuration > Configuring Intelligent Routing >
Configure rerouting analysis so that all outgoing calls from users in a specified call source are routed through the specified office route.
Scenario Description
Figure 1 Intelligent routing network diagram
The unified gateway of V2.0 and later versions supports configuration of the call source for rerouting analysis in the web management system. The unified gateway connects to carrier network through the PRA and ISUP trunks. The office route selection code is 1. Assume that user data and trunk data have been configured.
Assume that: When users 5032 to 5049 in call source 1 dial prefix 9 corresponding to office route selection code 1, calls are routed through the PRA trunk. When users 5050 to 5063 in call source 2 dial prefix 9 corresponding to office route selection code 1, calls are routed through the ISUP trunk. The data plan is as follows:
ϒ⁄Office route 0, used for the PRA trunk, corresponding to office route selection code 1 and call source 1
ϒ⁄Office route 1, used for the ISUP trunk, corresponding to office route selection code 1 and call source 2
Procedure
1.Log in to the web management system. For details, see Logging In to the Web Management System.
2.Configure an office route select code.
a.Choose Trunk > Office Route Configuration > Office Route Selection Code.
b.Clcik Create.
c.Configure office route selection code 1, as shown inFigure 2.
Figure 2 Configuring office route selection code 1
Table 1 describes the key parameters. For more details about the parameters, see the online help of the web management system.
Table 1 Key parameter description
Parameter |
Description |
Office route selection code |
Office route selection code of an office route. Each code identifies to an office route selection policy. |
Office route selection policy |
Policy for selecting among office routes with the same office route selection code. The options are as follows: ϒ⁄None Office routes are polled based on office route IDs in ascending order until an office route that contains idle circuits is found. ϒ⁄By Time Office routes are polled based on office route IDs in ascending order until an office route that is valid at the current system time and contains idle circuits is found. ϒ⁄By Charging Rate Office routes are polled based on charging rates in ascending order until an office route that contains idle circuits is found. Office routes with the same charging rate are polled based on office route IDs in ascending order. If no idle circuit is found, office routes configured with no charge rate are polled based on office route IDs in ascending order until an office route that contains idle circuits is found. ϒ⁄By Load Sharing Office routes are polled based on office route IDs in ascending order until an office route that contains idle circuits is found. The later calls will poll office routes from the next office route after an office route is selected by the preceding call. ϒ⁄By Load Sharing Percentage Except the office routes whose load percentages are set to 100%, office routes are polled based on the load percentages in descending order. ϒ⁄User Level Office routes are polled based on user priorities in ascending order until an office route that contains idle circuits and has an equal or lower user priority is found. Office routes with the same charging rate are polled based on office route IDs in ascending order. ϒ⁄Load Balancing Office routes are polled based on office route IDs in ascending order until an office route that contains the maximum number of idle circuits is found. |
Failure Processing Index |
Index of a routing failure processing policy related to the office route selection policy. For details, see Configuring Rerouting. |
Whether to send the two-stage dialing tone |
Indicates whether a user can hear the second dialing tone after dialing the outgoing prefix when making an outgoing call through an office route selected from the current office route selection code. |
a.Click OK.
Office route selection code 1 is configured.
2.Configure office route.
a.Office route 0 is used for the PRA trunk, with office route selection code being 1 and time segment index being 1.
b.Office route 1 is used for the ISUP trunk, with office route selection code being 1 and time segment index being 2.
c.Choose Trunk > Office Route Configuration > Office Route.
d.Click Create.
e.Configure the office route to 0, as shown in Figure 3.
Figure 3 Configuring office route 0
f.Click OK.
Office route 0 is configured.
g.Click Create, and configure office route 1, as shown in Figure 4.
Figure 4 Configuring office route 1
3.Configure the outgoing prefix.
a.Choose Trunk > CalleePrefix Configuration.
b.Click Create.
c.Configure the outgoing prefix 9, as shown in Figure 5.
Figure 5 Configuring the prefix 9.
d.Click OK.
Prefix 9 is configured.
4.Configure the call source.
a.Choose Trunk > CallSource.
b.Click Create.
c.Configure the call source 1, as shown in Figure 6.
Figure 6 Configuring the call source 1
d.Click OK.
Call source 1 is configured.
e.Click Create. Configure call source 2, as shown inFigure 7.
Figure 7 Configuring the call source 2
5.Add users to call sources.
a.Choose User > SIP User.
b.Click Create.
c.Add users 50325049 to call source 1, as shown in Figure 8.
Figure 8 Adding numbers 50325049 to call source 1
d.Click OK.
e.Click Create, as shown in Figure 9.
Figure 9 Adding numbers 50505063 to call source 2
6.Configure rerouting analysis.
a.Choose Trunk > Rerouting Configuration.
b.Click Create.
c.Configure rerouting analysis for routing the outgoing calls from users 5032 to 5049 in call source 1 through the PRA trunk when they dial prefix 9 corresponding to office route selection code 1, as shown in Figure 10.
Figure 10 Configuring rerouting analysis
The RouteNo refers to the number of the office direction to which the call source is bound. After the configuration is complete, you can run the show routeanalysis command to check the binding between the call source and the route number.
d.Click OK.
e.Click Create. Configure rerouting analysis for routing the outgoing calls from users 5050 to 5063 in call source 2 through the ISUP trunk when they dial prefix 9 corresponding to office route selection code 1, as shown in Figure 11.
Figure 11 Configuring rerouting analysis
Parent Topic: Configuring Intelligent Routing